But it was making great oil pressure right when it happened. Made from tough, rigid steel. PaceSetter Performance Products is a manufacturer. The factory system simply has too many non-optimized bends sharp bends, varying radii which, while functional, are not conducive to the passage of exhaust from a performance perspective. It is the responsibility of the customer to reinstall these devices on the vehicle. Coated at the factory with a non hi-temp black paint for pre-installation protection only.
It should be the same cost or less than a cat-back system. PaceSetter will not be responsible for freight, labor, other expense incurred, or inconveniences or damages caused by failure of the product, or for breach of any expressed or implied warranty with respect to the product other than as set forth herein. Comes with collector reducer 6. No noise, no jerking, no nothing. Or you can put long-tube headers on, as these will also eliminate the pre-cats.
It is made from stainless steel material for extended durability. The starter tries to turn over the engine but might get one or two turns before it stops. For service under the terms of this warranty the end user must be able to prove date of purchase. I took off the serpentine belt and tried to turn the crank by hand with a 3 foot breaker bar, but it wouldn't budge. All Replacement brand items are backed by 1-year, unlimited-mileage warranty.
This way, there was no need to remove any trans or motor mounts. When Ford designed these engines to go over 250K, they did not consider the longevity of these components. This will burn off on first use. Aftermarket cat-backs do away with this restriction by using stainless steel for maximum longevity , all mandrel-bent tubing throughout their length. When my driver's side exhaust manifold to down pipe stud broke, further inspection showed a crack at one of the flanges and the need to replace both cast iron manifolds.
Exceptions set forth below: 1st year of the warranty, PaceSetter will repair or replace products with defects in workmanship and materials. I know this is an old thread, but I had to do this to my '97, so will pass on the experience, being that eXoR never got a response. It acts like it is trying to turn the motor and tranny when you try and start it in neutral, and I could roll it in gear with no problem with the key off. Dynomax is a world leader in the performance exhaust space, manufacturing products held to the highest engineering standards and backed by extensive research and development. I guess while I have it out I might as well do the headers and cams and build it up the way I want. This will return a list of current local stocking resellers and online stores Unleash the power under your hood! There was nothing left of the heads of the manifold nuts to get a wrench around. What is the easiest way to get to them to cut them off with a die-grinder or anything? Or you can gut them and run a pipe thru them.
I post pics of how bad I trashed it as it comes apart and install photos as well. No smog or engine management hook-ups O2 sensor fittings when required 5. Oversize fees also waived on this item. When I replaced with the new manifolds, I thought it would be nice to use at least stainless nuts for the next guy, but after recently replacing the truck 210k with a low mileage '05, it probably will never be done again. Plating on a product, once the product is installed, is not covered under the terms of this warranty.
I went out and bought a remote cable drive for my Dremel tool. My cell is 937-260-6943 if you want to call and ask me more. Or you can gut the pre-cats. I have to have this truck for work since I work out of it. All Pacesetter products combine over 45 years of commitment to provide quality-made, affordably priced American-made auto-parts to the automobile enthusiast. .
Shipping to PaceSetter is responsibility of customer. Valid on orders shipped in the contiguous United States. Furthermore, aftermarket cat-backs feature a variety of mufflers, that one, flow easier, and two, sound much, much better. Also voiding the warranty are uses contrary to applicable instruction sheets, shipping damage, header wrap or repair performed by other than PaceSetter. Established in 1908, Walker is renowned in the automotive aftermarket for manufacturing a full line of exhaust system parts.