Posted on Jan 10, 2010 When you install Windows 10, it usually finds most of the peripheral devices and installs drivers for them. What kind of communication did you use or did you reteive the data after flight? Posted on Sep 12, 2012 If you commit to Igolf access free or subscription , be aware that it is mmarried to Java Script version 6. Most modules actually contain a supercapacitor that looks like a button battery. I believe it's the firmware that is in the demo unit. No download or membership fees ever. The configuration gets lost after a few minutes without power.
The neo series is great but this iGolf married is playing havoc on your customers! As default receiver baudrate is usually also 9600 this may not be needed. Jan 31, 2016 I had the same problem with my bushnell neo plus. Antenna is external active antenna and connects to the module via ufl connector. Posted on Feb 12, 2011 The wording on this question is almost word for word of a message I sent iGolf customer support. Do you have a writeup of your system maybe? I had the same problem with my bushnell neo plus.
Then it reverts back to 1000ms. If you have already switched to Java version 7, it just won't work. Most of the time i only get the time and date form the gps. This worked out really well and I changed and saved both the baud rate and the sentences. But again everthing works, satallite signal strong, courses are loaded but no yardage is shown. The other Java program on there is compatible.
I know for sure that the map loading requires some wizard. It changes and runs at 250ms until I do the save config and send. However the software on the station was already programmed and needed a fixed 57600 baudrate. It is incompatible with the Neo sync application. Do you have a sattelite lock problem or does apm not connect to the gps? The protocol is well documented in the module manual. Locks on pretty quickly, is accurate and gives me yardage so I can pick the right club. I was able to setup my profile and sync my device without a problem.
You can try selecting an airborne mode if that helps. So when you hit checkout, please be sure to select a Standard Ground service option! The module was to be connected to a ham radio station for tracking data transmission. With such high altitudes the normal equations used by the chipset may get bad results just my assumption. If it's my message I don't know how it showed up here on fixya. Also no way to tell what kind of fix the receiver is getting and the quality of positioning. You could add another led parallel to the one already mounted. The builder said it needs to be 4800 8,N,1.
Now I know exactly what the distance is from where I stand. Also i'm not entirely sure if it will go off if the fix is lost would have to try that. Somebody returned these items to The Cave without ever using them. Thanks for your great article. The module seems to have quite good reception and also the start times are pretty nice, usually under a minute even under a bit more difficult conditions in house. I read some datasheets and circuit diagrams. Inside it doesnt work at all.
It now works using that baud rate,but still does not work on the encoder I bought. It worked immediately without even restarting. I had removed Java re: all the recent security issues being discussed and installed V7. The place I purchased the encoder from said it needs to be 4800 baud rate,not 9600. I connected it with my arduino, but i dont get a fix. I suggest you to save to all available devices at the same time.
The other Java program on there is compatible. I waited over an hour outside. I tried the above Best Solution, but on the newer computers, I get a message saying the Vista driver is only for Vista, not for Windows 7. By default my module was programmed to send the basic location information once per second 1Hz data and at the baudrate of 9600 baud. Google: neo Java and you'll begin to see the problems.
I was able to setup my profile and sync my device without a problem. I guess this is a bit more on advanced side but can be useful if you want to change the module configuration on-the-fly from your own program. No support from either Bushnell or Igolf on this. Solution: 1 Click on your Start Menu 2 Select Computer 3 Open Local Disk C. Then I wwas back to it working. If there is no Windows 10 driver package, most Windows 8. On pcb there are also a 3.